Vaults (HUC-4)

Vaults (HUC-4)

Built to Protect.

Hubbell Vaults – the preferred alternative Providing the protection you depend on for transformers and power cables, Hubbell Un derground Vaults can be buried flush with the ground where they’re literally out of sight. Dramatically improving the appearance of the surrounding landscape, Hubbell Vaults are conveniently lightweight but strong enough to meet ANSI TIER rating requirements. They can be used as a pad for single-phase transformers and a variety of load-break junctions.

INTRODUCTION

Page 2 | April 2011

TABLE OF CONTENTS

Introduction...................................................................... 2 Table of Contents. ............................................................ 3 Underground Distribution Switchgear Vaults. ............... 4 Installation.....................................................................5-6 DRAWINGS: Switchgear Vaults with Torsion Assist Covers..............7-8 Below Grade Sectionalizing Vaults.............................9-10

TABLE OF CONTENTS

Numbering System Key.................................................. 11

Page 3 | April 2011

Underground Distribution Switchgear Vaults

Hubbell Underground Distribution Switchgear Vaults utilize both Polymer Concrete and FRP con struction to guarantee a simple, lightweight, and lower-cost alternative to the heavy, expensive concrete vaults used for underground distribution switchgear. Hubbell’s designs ensure freedom from rust and corrosion in all environments. Our unique technology enables us to construct vault enclosures with an unequaled blend of strength, durability, and ease of installation. We offer mul tiple sizes for both four-way and six-way switchgear.

Designed To Be Superior

Lightweight - Hubbell Underground Distribution Switchgear FRP Vaults weigh just 4,000 pounds. Com pare that to traditional concrete enclosures, which are incredibly heavy and can weigh as much as 20 times more. The greatly reduced weight means considerable savings on labor, time, and expense. Strength – Hubbell Vaults boast compressive, flexural, and tensile strengths three to five times higher than traditional concrete. Cost Savings - Unlike much heavier concrete models, Hubbell Vaults can be set with excavation equip ment already on site.

Less Red Tape - No special transportation permits are required.

Fewer Headaches - No cranes are required for installation or access.

Cover Options - There are multiple easy-access cover openings available including torsion, polymer concrete, or ultra-lightweight composite covers. Torsion covers open to 180 degrees for ease of access. Additional Options - These may include composite work and switchgear platforms, composite ladders, racking, terminators, and pulling eyes.

SWITCHGEAR ENCLOSURES

Page 4 | April 2011

Installation

Guidelines for installing Hubbell Vaults may vary depending on size, location, and environmental factors. Hubbell Vaults are designed for non-deliberate traffic areas only. Install Vaults by fol lowing four simple steps.

INSTALLATION

Site Selection Select an appropriate site or location that is suitable for a Vault. Site features to consider prior to final selection include: o Utility easements o Streets o Parking lots o Parking lot entrances o Shipping and delivery docks o Waste-removal containers (dumpsters) 1 Conduits and Piping Preparation • Trench and/or plow conduit. • Bore under road crossings & railroads. • Mark the depth of conduit using marker tape. 2 Excavate • Excavate approximately 1-2 feet longer and wider than the Vault, and 6-8 inches deeper than the depth of the Vault. • Add a rodent barrier if necessary. 3

Attach nylon straps or chains to the lifting bolts.

Lift and position enclosure with backhoe.

CONTINUED . . .

Page 5 | April 2011

Install and Protect Environmental factors should always be considered when installing enclosures of all sizes. Local conditions could dic tate additions during installation, such as Concrete Collars or Internal Bracing. These additions provide security, sup port, and protection.

Placement • Remove Vault from the pallet to prepare for placement. • Place nylon straps or chains around the lifting bolts and secure it to the backhoe bucket. The angle between the strap and the Vault should not be less than 45 degrees. • Lift the Vault and place it into the hole. • Place gravel in the Vault and around the side if necessary. • Lift the Vault to the proper elevation, allowing gravel to run out under the Vault. • Check the Vault’s elevation with a level and range pole, and make the necessary adjustments with the backhoe bucket. • Once the Vault is set to the proper elevation, reinstall the covers, and back fill. • If 95% compaction is required, internal bracing should be used on all manufacturers’ Vaults to prevent deflection and damage. 4

INSTALLATION

Place gravel in the enclosure and around the side. Lift enclosure to let gravel run underneath.

Page 6 | April 2011

Dimensions / Data CORRUGATED SWITCHGEARVAULTSWITHTORSION ASSIST COVERS

VAULT DRAWINGS

Corrugated Switchgear Vaults with Torsion Assist Covers

DESIGN / TEST LOAD 8,000 / 12,000 8,000 / 12,000 8,000 / 12,000

PALLET QTY

A

B

C

D

E

F

G

TIER

PART NO.

102 1/2

84 1/2

98

74 1/2

35 5/8

35 5/8

59 3/4

8 8 8

1 1 1

A1A7896501 A1A9696501 A1A1011501

112 108

114 116

107 104

109 109

48 48

48 41

88 88

Page 7 | April 2011

Dimensions / Data

POLYMER CONCRETE SWITCHGEARVAULTS

VAULT DRAWINGS

Polymer Concrete Switchgear Vaults

Cover Option Torsion Assist

TIER

DESIGN / TEST LOAD PALLET QTY

PART NO. PB9393Z502 PB9393Z505

8 8

8,000 / 12,000 8,000 / 12,000

1 1

Polymer Concrete Removable

NOTE: Ultralight removable covers are available. Contact customer service for further details.

Page 8 | April 2011

Dimensions / Data CORRUGATED BELOW GRADE SECTIONALIZINGVAULTS - 1 PHASE

MOUNTING BAR INSTALLATION

Corrugated Below Grade Sectionalizing Vaults – 1 Phase Box A B C WEIGHT

VAULT DRAWINGS

PALLET QTY

PART NO. B1A3048507 B1A3048508

49 7/8 49 7/8

32 3/8 32 3/8

36 48

218 236

1 1

NOTE: Factory installed junctions available by customer request. Tier 15 & Tier 22 ratings are available. Contact customer service for further details.

Corrugated Below Grade Sectionalizing Vaults – 1 Phase Cover

DESIGN/ TEST LOAD 8,000 / 12,000

DESCRIPTION

TIER

WEIGHT

PALLET QTY

PART NO.

w/ 2 bolts

8

165

3

C1A304803A

NOTE: Ultralight removable covers are available. Contact customer service for further details.

Page 9 | April 2011

Dimensions / Data CORRUGATED BELOW GRADE SECTIONALIZINGVAULTS - 3 PHASE

MOUNTING BAR INSTALLATION

OPTION B

VAULT DRAWINGS

OPTION A

Corrugated Below Grade Sectionalizing Vaults – 3 Phase Box

A

B

C

OPTION

WEIGHT

PALLET QTY

PART NO. B1A3060509 B1A3060510 B1A4848510 B1A4848511

62 1/2 62 1/2 52 7/8 52 7/8

34 1/2 34 1/2 52 7/8 52 7/8

36 48 36 48

A A B B

263 286 301 327

1 1 1 1

NOTE: Factory installed junctions available by customer request. Tier 15 & Tier 22 ratings are available. Contact customer service for further details.

Corrugated Below Grade Sectionalizing Vaults – 3 Phase Cover

DESIGN/ TEST LOAD 8,000 / 12,000 8,000 / 12,000

DESCRIPTION

TIER

WEIGHT

PALLET QTY

PART NO.

w/ 2 bolts w/ 2 bolts

8 8

165 165

3 3

C1A306003A C1A484803A

NOTE: Ultralight removable covers are available. Contact customer service for further details.

Page 10 | April 2011

CatalogNumbering Systemfor Polymer ConcreteVaults

1 Weight

2 Style

3,4 5,6 Size

7,8,9,10 Variation

P

B

93 93

Z502 (Torsion Assist Cover) Z505 (Polymer Concrete Cover)

NUMBERING SYSTEM KEY

CatalogNumbering Systemfor CorrugatedVaults

1 Item

2 Assembly/ Cover 1 (1/2-13 UNC Penta Head Bolts)

3 Style

4,5,6,7 Size

8,9,10 Variation

A (Assembly) B (Box) C (Cover)

A (CorrugatedWall Box/Square Corner Cover - Tier 8)

7896 9696 3060 4848 3048

XXX

Page 11 | April 2011

Hubbell Enclosures 780 West Granada Boulevard, Suite 300 • Ormond Beach, Florida 32174 Phone: 386.615.9510 • Fax: 386.615.9606 • hubbellenclosures@hubbell.com

NOTE: Because Hubbell has a policy of continuous product improvement, we reserve the right to change design and specifications without notice. ©Copyright 2011 Hubbell Incorporated

Page 12 | April 2011 NEVER COMPROMISE ™ www.hubbellpowersystems.com

APRIL 2011 5M RGS 4/11

Catalog # HUC-4

Made with FlippingBook - Online Brochure Maker