Chance Technical Design Manual

The total side resistance (Q f ) is then obtained from:

Adhesion as a Function of Undrained Shear Strength

EQUATION 5-23

Q f = π d(L)f s

where

d = Diameter of central shaft L = Length of round shaft in contact with soil The design line given by the American Petroleum Institute (API) shown in Figure 5-11 may also be used in which: For s u < 500 psf, a = 1.0 For s u > 1500 psf, a = 0.5 For 500 psf < s u < 1500 psf, a varies linearly between 1.0 and 0.5 The side resistance should only be calculated for that portion of the shaft length that is in full contact with the soil. This will depend on the length of the lead section, the design of the shaft couplings that connect the pile sections, and the type of soil. In the case of flush connections between extension sec tions, the entire shaft is in full contact with the soil. On the other hand, flanged and bolted connections generally create an annulus between the shaft and soil as the pile or anchor is installed as shown in Figure 5-12c. This is because the coupling, being larger than the shaft, displaces and compacts soil. Gen erally, the length of the central shaft between couplings is not considered to develop side resistance unless the disturbed soil moves back against the shaft or sufficient time is allowed for the soil to recover. If side resistance is calculated for shaft lengths where soil recovery has occurred between couplings, reduced shear strength should be used for the soil in those zones. 5.2.4.2 SIDE RESISTANCE IN SANDS AND MIXED SOILS ( φ ’ > 0; c ≥ 0) The side resistance of steel round shaft piles and anchors in coarse-grained soils, such as sands and mixed soils, is more complex than in clays but can still be determined using tradi tional deep foundation analyses. The Department of the Navy Design Manual DM-7 also gives a simplified method for esti mating the unit side resistance for straight-shaft steel piles. The value of f s is related to the friction angle of the soil ( ϕ ’) and the effective vertical stress ( σ ’ vo ) as given in Table 5-4. VALUES OF UNIT SIDE RESISTANCE FOR STEEL PILES IN SAND [NAVY MANUAL DM-7 (1974)], TABLE 5-4

Adhesion Factor, a

VARIATION IN ADHESION FACTOR WITH UNDRAINED SHEAR STRENGTH OF CLAYS [CANADIAN FOUNDATION MANUAL (2006)] FIGURE 5-9

5.2.5 HELICAL PILE/ANCHOR SPACING AND MINIMUM DEPTH 5.2.5.1 REASONABILITY CHECK It is important to evaluate the validity of the values obtained when determining the bearing capacity and side resistance of the soil. The calculated theoretical ultimate capacity is no better than the data used to obtain that value. Data from soils reports, boring logs, the water table depth, and load information may not accurately represent actual conditions where the helical pile/anchor must function. Empirical values that are used and estimates of strength parameters, etc. that must be made because of lack of data affect the calculated bearing capacity and side resistance value. In situations where soil data is insufficient or not available, a helical trial probe pile/ anchor can help determine data such as the location of bearing strata, pile/anchor capacity, the location of soft/loose soil, and the presence of obstructions such as cobbles, boulders, and debris. An important step in the process of determining the capacity of a helical pile/anchor is to conduct a reasonability check. The engineer should use the best engineering judgment to perform the reasonability check. This should be based on experience, historical test data, and consulting colleagues. This is easily overlooked but must be performed by the designer or by others. 5.2.5.2 HELICAL PILE/ANCHOR SPACING Once the capacity of the helical pile/anchor is determined, turn attention to the location of the foundation element with respect to the structure and to other helical piles/anchors. It is recommended that the center-to-center spacing between adjacent piles/anchors be no less than five times the diameter of the largest helix. The minimum spacing is three feet (0.91m).

FRICTION ANGLE OF SOIL ( φ ’)

s ’ vo (psf)

20

25

30

35

40

UNIT SIDE RESISTANCE (f s ) (psf)

500

137

175

217

263

315

1000

273

350

433

525

629

DESIGN METHODOLOGY 1500 410

524

650

788

944

2000

546

700

866

1050

1259

2500

683

875

1082

1313

1574

3000

819

1049

1300

1575

1888

3500

956

1244

1516

1838

2203

4000 1092

1399

1732

2101

2517

Page 5-12 | Hubbell Power Systems, Inc. | All Rights Reserved | Copyright © 2023

Made with FlippingBook - professional solution for displaying marketing and sales documents online