CA01082E_Catalog 30

30 - ARRESTERS

Hardware Line and Ground Terminals - All Hubbell arresters include as standard line and ground terminals for conductors from 0.25 (7) to 0.81 (21) inch (mm) diameters. These are made from hot-dipped galvanized (HDG) malleable iron, compatible with either aluminum or copper. To obtain a full replacement hardware kit for an EVP arrester with standard hardware, specify part number PSCPTERMKIT01. The arrangement of mounting terminals on arresters makes it possible to align them in any direction to accommodate the angle of the incoming lead wire. If your conductor size exceeds standard terminal capacity, contact your Hubbell Power Systems Representative at 1.573.682.5521 for an appropriate quote. .19 1.75 1.75 .56 - 4 HOLES 3.3 .19 1.75 1.75 .56 - 4 HOLES 3.3 1.75

.56 - 4 HOLES

1.38

.62

.62

.19

3.12

HDG Terminal Assy, Part No. M271414-3001 Suitable for Cu or AI conductor size 0.25 (7) to 0.81 (21) inch (mm) diameter. (AWG#4 – 500 MCM) .19 1.75 3.3

HDG 4-HOLE TERMINAL PAD, PART No. 274914-4002 HDG 4-HOLE TERMINAL PAD, PART No. 274914-4002

OLES

HD SUI .25

1.06 1.06

1.38 1.38

1.75

.62

3.12

1/2-13 UNC-2A THREAD

1/2-13 UNC-2A THREAD

1.06

1.75

3.3

.62 HDG 4-HOLE TERMINAL PAD, PART No. 274914-4002

2.875 2.875 HDG TERMINAL ASSY, PART No. M271414-300 SUITABLE FOR Cu OR Al CONDUCTOR SIZE .25 - .81 DIA (AWG#4 - 500 MCM) HDG TERMINAL ASSY, PART No. SUITABLE FOR Cu OR Al CONDU .25 - .81 DIA (AWG#4 - 500 MCM) .56 HOLE 0.9 0.9 2.19 .56 HOLE 2.875 .56 HOLE .56 HOLE 0.9 2.19 2.19 1/2-13 UNC-2A THREAD

HDG Terminal Bracket Assy, Part No. M71874-3001 Suitable for Cu or AI c onductor Size 0.25 (7) to 0.81 (21) inch (mm) diameter. (AWG#4 – 500 MCM)

-HOLE TERMINAL PAD, PART No. 274914-4002

.56 HOLE .56 HOLE

1.59

1.59

HDG TERMINAL BRACKET ASSY, PART No. M71874-300 SUITABLE FOR Cu OR Al CONDUCTOR SIZE .25 - .81 DIA (AWG#4 - 500 MCM) HDG TERMINAL BRACKET ASSY, PART No. M71874-3001 SUITABLE FOR Cu OR Al CONDUCTOR SIZE .25 - .81 DIA (AWG#4 - 500 MCM)

Suspension Cap, Part No. 90170-4001 2.875

.56 DIA 3 HOLES .56 DIA 3 HOLES

1.75 1.75

.50 .50

2.19

1.75 1.75

.69 DIA HOLE FOR LIFTING 69 DIA HOLE FOR LIFTING

0.9

This cap is the standard suspension cap furnished with VL, SVN, PH3, PH4, MVN, MH3 and MH4 arresters. Part No. 272087-3001K includes the suspension cap, terminal assembly and mounting bolts 2.875 .56 HOLE 0.9 .56 HOLE

5.63 5.63

.56 HOLE

.56 .56

2.19

1.59

3 @ 120° ON 10.0 B.C. 2.25 LG, NUT & LOCKWASKER 1/2-13 UNC-2A BOLT 1/2-13 UNC-2A BOLT 2.25 LG, NUT & LOCKWASKER 3 @ 120° ON 10.0 B.C.

.56 HOLE

Part Number: 272087-3001K

1.75 HDG TERMINAL BRACKET ASSY, PART No. M71874-3001 SUITABLE FOR Cu OR Al CONDUCTOR SIZE .25 - .81 DIA (AWG#4 - 500 MCM) 1.59

4-Hole NEMA Pad, Part No. 274914-4002 4-Hole NEMA Pad, Part No. TERMINAL BRACKET ASSY, PART No. M71874-3001 ABLE FOR Cu OR Al CONDUCTOR SIZE 81 DIA (AWG#4 - 500 MCM) .56 - 4 HOLES 3.3

.56 - 4 HOLES .56 - 4 HOLES

1.75

1.38

.19

.19

.19

1.06

1.75 1.75

1.75

3.3

274914-4002 Line-end terminals are available with a 4-hole NEMA pad with a single eye-bolt. Single eye-bolt ground-end terminals are automatically included. The 4-hole NEMA pad is typically furnished with standard EVP & PVI-LP end codes.

.62 .62

1/2-13

HDG 4-HOLE TERMINAL PAD, PART No. 274914-4002

HDG 4-HOLE TERMINAL PAD, PART

HDG TERMINAL A SUITABLE FOR Cu .25 - .81 DIA (AWG

Engineering Note: Maximum recommended tightening torque to be applied to the end stud when installing terminals and leads is 40 ft-lbs (54 Nm).

www.hubbell.com/hubbellpowersystems | 30-61

2.875

2.875

2.19