BRYANT 2021 Full Line Catalog (BC003 1/21)
IEC 60309 Pin and Sleeve Devices Technical Specifications - Watertight
IP67 Suitability
Listings UL Listed Standard 1682 (plugs, receptacles, and cable connectors of the pin & sleeve type) Conforms to UL 1686 (pin & sleeve configuration)
CSA Certified C22.2 No. 182.1 - 13 Complies with IEC 60309-1 and 60309-2 International Standards for singly-rated non-interchangeable configurations CE
Materials Plug/Connector
Receptacle/Inlet
Housing, gland nut and cord clamp assembly
Toughened nylon
Housing/mounting flange Mounting screws
Toughened nylon
Cord gland
Neoprene
Stainless steel
Seals/gaskets
Neoprene, EPDM, TPE
Seals/gaskets
Neoprene, EPDM, TPE
Phase/ground pins Terminal screws
Brass
Phase/ground pins Terminal screws
Brass
Plated steel
Plated steel
Terminal cover
Toughened nylon Glass-reinforced nylon (100A)
Terminal cover
Toughened nylon Glass-reinforced nylon (100A)
Contact carrier
Glass-reinforced nylon, Nylon (60A)
Contact carrier
Glass-reinforced nylon, Nylon (60A)
Gland friction washer
Plated carbon steel (30/60/100A) Nylon (20A)
Receptacle Cover arm Cover ring
Toughened nylon Polycarbonate
Assembly screws
Stainless steel (60/100A) Plated steel (20/30A)
Sleeve spring Sleeve spring
Nickel-plated spring steel Nickel-plated spring steel
Plug
Locking ring
Polycarbonate
Hinge pins
Brass
Connector Cover ring
Polycarbonate Stainless steel
Inlet
Cover spring
Mounting flange
Toughened nylon
Hinge pins
Brass
Locking ring
Polycarbonate
Sleeve spring
Nickel-plated spring steel
Assembly screws
Stainless steel (60/100A), plated steel (20/30A)
Performance Electrical Dielectric voltage withstand Max. working voltage
Environmental
3,000 Volts - receptacle, 2,200 Volts - plug and connector
Moisture resistance
Submerged 24 hours at 2" below water surface
600 Volts AC
Flammability (enclosure)
V2 minimum per UL 94
Spacings
¼" minimum creepage and clearance per UL 1682 Certified for current interrupting at full rated current where applicable per UL 1682 Less than 30°C temperature rise at full rated current after 50 cycles of overload tested at 150% of rated current at 0.75 pf. Up to 5,000 connect and disconnect cycles at full rated current and voltage per UL 1682 After 6 hours at -25°C, 8 drops from 2½' with 7½' length cord 250 lbs. force for 1 minute after 6 hours at -25°C Terminals identified in accordance with North American Codes Catalog number and rating indicated on device
Operating temperatures Maximum continuous 95°C with impact, minimum continuous -40°C without impact
Current interrupting
Ingress protection
IP67 suitability
Temperature rise
Polarization integrity
Mating devices will not energize ground if polarization feature is removed from housing and 40 lbs. force is applied
Endurance
The following international electrical regulatory agencies recognize IEC 309 standard Pin & Sleeve devices
Mechanical Impact resistance
OVE
CEBEC
Mechanical crush test
Austria
Denmark
Belgium
CzechRepublic
Terminal identification
I
D V E
Product identification
Finland
Germany
Great Britain
Hungary
EMA EUR K
Netherlands
Sweden
Italy
Norway
K-12
www.hubbell.com/bryant/en/
Specifications are subject to change without notice.
Made with FlippingBook Digital Proposal Maker